what do I do if there are holes in between my knots help!!!
Reply
|
vscogirl80
Professional
 |
5 years, 1 month ago by vscogirl80
Someone please help whenever I make bracelets there are always holes inbetween the knots I’ve been struggling for a while and it makes me discouraged because I can’t figure out what I’m doing wrong someone plssssss help me!!! 🥺😭
|
|
poppit
Bracelet King
 |
5 years, 1 month ago by poppit
I think it’s probably that you are tying you’re knots quite loose.You could try tying them tighter, being especially careful with the first half of the knot because the second half is just to secure it. I hope that helped. |
|
fionaruane
Professional
 |
5 years, 1 month ago by fionaruane
in my experience there's a couple of things that could be causing this. check your knots and make sure they're not only tight but consistent with one another. also make sure that you're not skipping ANY knots in the pattern as obviously this prevents the intended pattern from turning out the way you wanted. when i get this issue i try to kinda 'zone-out' so i don't overthink my knots and they usually end up more consistent that way. good luck!
|
|
CoolKnot
Bracelet King
 |
5 years, 1 month ago by CoolKnot
I’ve found 2 very solid reasons for this problem... and I’ve tested it out myself. It could either be your consistency of your knots, or the thickness of your thread. Sometimes when your distracted while making bracelets you tie certain knots tighter than others... and there tends to be holes sometimes especially if you pattern has a lot of fb or bf knots. And if you you various brands of string like I do... some strings tend to make bigger knots than others and end up leaving holes sometimes because the knot sizes are different. I hope this helps! 😊
|
|
madeleine_
Moderator
 |
5 years, 1 month ago by madeleine_
Make sure that you’re tying your knots tightly, especially the first half, because that’s what determines the placement of the knot. Tying the first half loosely but the second half really tightly will still result in holes
|
|
sunnylemon
Bracelet King
 |
5 years, 1 month ago by sunnylemon
this happens to me too but I think it's because the strings kind of go apart from each other if that makes sense. Is there a way to fix that?
|
|
vscogirl80
Professional
|
5 years, 1 month ago by vscogirl80
Thanks everyone for the tips
|
|
Clairaland
Bracelet King
 |
5 years, 1 month ago by Clairaland
Try tying your knots tighter
|
|
_laurennn_
Advanced
 |
5 years, 1 month ago by _laurennn_
Sometimes this happens to me too! When it happens i usually go back and tie the first half of the knot tighter and make sure all of my other knots are tight too.
|
|
amazingme
Bracelet King
 |
5 years, 1 month ago by amazingme
It's your knot tension. You should tighten the first knot, then make that second knot slightly loose compared to the first. It also helps if you segment knot instead of row by row
|
|
MintBreez
Bracelet King
 |
5 years, 1 month ago by MintBreez
Make sure you tie the first half of the knot first super tight, and if you don't like where it is positioned move it with your fingernail, and then tie the second half of the knot. Masha Knots also has a video:https://www.youtube.com/watch?v=PoOzRaHoY5U Hope this helps! |
|
Crafty_K
Bracelet King
 |
5 years, 1 month ago by Crafty_K
Keeping your knots super tight is a good way to prevent holes from forming. Make sure the amount of tension on your knots are even, for example not too tight, and not too loose. That also helps to prevent holes. Hope this helps!!
|
|
BubblyCraf
Bracelet King
 |
5 years, 1 month ago by BubblyCraf
My knots used to be like that too, but then I started making sure that both halves of the knot were as tight as possible (almost) What I would say to do is to make sure that you are tying both halves as tight as you can so that it will stay in the position you want.
|
|
vscogirl80
Professional
|
5 years, 1 month ago by vscogirl80
@MintBreez what is the video called
|
|
MintBreez
Bracelet King
|
5 years, 1 month ago by MintBreez
I gave you a link, but the video is called "Beginner Mistakes"
|
|
-cupqake-
Professional
 |
5 years, 1 month ago by -cupqake-
Also, the more you make bracelets, the better you will get! You will develop techniques and soon, you won’t see holes!
|
|
eedeetv
Bracelet King
 |
5 years, 1 month ago by eedeetv
The holes between knots is caused when you don't tighten the first half of your knot enough! Try tightening the first half, making sure the knot is exactly where you want it to be! Hope this helps! 🙂
|
|
garanceles
Advanced
 |
5 years, 1 month ago by garanceles
just try tying ur knots tighter, it will come wiht practice!!
|
|
jdelauter
Professional
 |
5 years, 1 month ago by jdelauter
make your knots tighter if that doesn't work it could be your string
|
|
JulkaW
Bracelet King
 |
5 years, 1 month ago by JulkaW
One knot is basically made up of two knots: the first one determines the placement of the knot and the second one just keeps it in place. So if you make the first one tighter it will bring the knot closer to all the other knots and hopefully there wont be a hole!
|
