What do you use to hold down your string?
Reply
|
ilovemasha
Professional
 |
4 months, 3 weeks ago by ilovemasha
I used to use a binder and a clip but now I have nothing to use, no tape nothing! So what should I go buy that works best?
|
|
halokiwi
Moderator
 |
4 months, 3 weeks ago by halokiwi
For me a binder clip works best.
|
|
pulserasAG
Bracelet King
 |
4 months, 3 weeks ago by pulserasAG
I use binder clips in a wood board! and it's very usefull!
|
|
BobTheCat_
Professional
 |
4 months, 3 weeks ago by BobTheCat_
I usually use tape on my thread box, but i will admit it is not the best solution lol. The tape sticks really well but due to the slipperiness of the thread box sometimes my bracelets slide down. And it's a pain to peel all the tape off, especially after a long complicated alpha 😤 😄
|
|
cecibee87
Bracelet King
 |
4 months, 3 weeks ago by cecibee87
I use a clipboard
|
|
201217
Bracelet King
 |
4 months, 3 weeks ago by 201217
Binder clip, tape or my toe 😉
|
|
ashlatano
Advanced
 |
4 months, 3 weeks ago by ashlatano
I usually attach the loop to my water bottle so I can make bracelets at school.
|
|
queenellie
Professional
 |
3 months, 3 weeks ago by queenellie
i tape them to my bobbin box or secure them with my owala
|
|
mrs_jordan
Bracelet King
 |
3 months, 3 weeks ago by mrs_jordan
I use duct tape on my desk
|
|
leviOsa_09
Bracelet King
 |
3 months, 3 weeks ago by leviOsa_09
i have a small clipboard that works! occasionally use a large binder clip too
|
|
kambri1224
Bracelet King
 |
3 months, 3 weeks ago by kambri1224
i tend to use a safety pin through the loop or tie so i can carry it around, however it does mean your bracelet moves a lot while you’re knotting so if that bothers you i wouldn’t go for it
|
|
goregirl
Bracelet King
 |
3 months, 2 weeks ago by goregirl
I use a clipboard, but I’ve used safety pins or just tape to the table
|
|
YoasobiLvr
Bracelet King
 |
3 months, 2 weeks ago by YoasobiLvr
I use tape and for travelling a safety needle.
|
|
dragonzzz
Bracelet King
 |
3 months, 2 weeks ago by dragonzzz
I use a safety pin to pin them to the knees of my pants, to hold the bracelet in place I put one end of the safety pin through the loop then the other end
|
|
Broken_Cow
Advanced
 |
3 months, 1 week ago by Broken_Cow
I find that tape normally doesn't work, so I'll use a clipboard for alphas, and I like to bring my normal bracelets with me to work on so I'll tie them on my water bottle
|
|
GiuseppeK
Bracelet King
 |
3 months, 1 week ago by GiuseppeK
Safety pinned to a pant leg when out in the wild, and secured to the handle of a small kettlebell on a table when I'm "at the office."
|
|
KnottyArty
Professional
 |
3 months ago by KnottyArty
For bracelets I use a mason jar! I put the start in between the flat lid and the part that screws into place.. I move the bracelet up when I need better tension or more working room….
|
|
KnottyArty
Professional
|
3 months ago by KnottyArty
For keychains, I recently started using this technique and I love it, perfect for the couch!! You got a tall laundry basket that has holes in the design? Take a piece of crap yarn and tie it between two of the holes where ever it comfortable on the basket! I also have a second string attached for other WIP that I can pick up and start when I want!
|
|
KnottyArty
Professional
|
3 months ago by KnottyArty
Both option have built in string compartments too!
|
|
01289
Professional
 |
2 months, 4 weeks ago by 01289
my toes I gripit between my big and pointer toe 🤮 🤪
|
